Measure and Cut New Treads

What happens in this clip

Measure each stair tread individually from front to back and side to side, as stairs are rarely perfectly uniform. Cut the new hardwood treads to the precise dimensions of each step. Double-check all measurements before making cuts to ensure accuracy.

Goal: Prepare new hardwood treads to fit each stair.

What's used

Tools

• Pencil
• Safety Glasses
• Saw (e.g.
• Miter Saw
• Table Saw
• Jigsaw)
• Tape Measure

Materials

• New Wooden Treads

About the full video

This DIY project guides you through completely renovating old carpeted stairs by removing the old carpet, cutting off existing bullnoses, securing loose stairs, installing new hardwood treads and risers, and finally staining them for a polished look.

Step 5 of 11: Measure and Cut Hardwood Treads and Risers

Measure the length of each stair tread from wall to wall or from nosing to nosing if applicable. Measure the height of each riser. Use these measurements to cut your hardwood planks. For treads, you may need to join multiple boards or use a wider plank. Ensure your cuts are straight and accurate. If your stairs have a bullnose or specific nosing profile, account for this in your measurements and cuts.

Open this step in the guide

Every video in How to Get a Hardwood Look on Carpeted Stairs

1. Step 1: Remove Carpet and Padding

   • 0:04–0:34 Remove Old Carpet and Padding
   • 0:21–0:50 Remove the Carpet
   • 0:44–2:00 Remove Old Carpet

2. Step 2: Remove Staples and Nails

   • 0:31–0:55 Remove Tack Strips and Staples
   • 0:13–0:38 Remove Carpet and Prep for Installation
   • 1:19–1:49 Remove Staples and Protruding Nails

3. Step 3: Inspect and Repair Stair Structure

   • 0:09–0:14 Repair and Prepare Stair Structure
   • 1:40–2:44 Prepare Surface by Filling Holes
   • 3:59–6:57 Replace Damaged Stair Treads or Risers

4. Step 4: Clean and Sand Stair Surfaces

   • 1:05–1:18 Vacuum Dust and Perform Fine Sanding
   • 0:51–0:57 Strip Old Finish from Tread Surfaces
   • 0:37–0:41 Sand the Staircase

5. Step 5: Measure and Cut Hardwood Treads and Risers

   • 6:09–11:07 Measure and Cut Treads
   • 0:43–0:52 Measure and Cut New Treads (this video)
   • 3:40–6:00 Measure and Cut Risers

6. Step 6: Install Hardwood Risers

   • 0:35–0:46 Install the Riser Boards
   • 2:49–3:19 Install Retro Risers
   • 3:55–5:35 Cut and Install Stair Risers

7. Step 7: Install Hardwood Treads

   • 10:00–11:40 Install Hardwood Treads and Risers
   • 0:49–2:35 Install the Tread and Nosing Components
   • 2:35–4:25 Secure New Stair Treads

8. Step 8: Install Stair Nosing (if applicable)

   • 4:41–5:53 Cut and Install Nosings
   • 0:37–0:41 Install Stair Nose Trim
   • 13:39–14:45 Measure and Install Stair Nosing

9. Step 9: Fill Nail Holes and Gaps

   • 16:00–16:30 Apply Wood Filler for Finishing Touches
   • 0:55–1:21 Apply Wood Filler to Blemishes
   • 0:07–0:25 Inspect and Fill Imperfections

10. Step 10: Sand Repaired Areas and Final Surface

    • 2:44–3:20 Sand Surfaces and Control Dust
    • 1:21–1:35 Sand and Clean Stairs
    • 1:47–2:00 Fill and Sand Risers

11. Step 11: Apply Finish (Stain and Sealant)

    • 0:45–0:59 Apply Protective Topcoat
    • 11:09–11:34 Apply Protective Wood Top Coat
    • 2:01–2:44 Apply Polyurethane Sealer